No part of this publication may be copied, distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language without the prior written permission of Digium, Inc. For HP D元20e G8 v2 all FXS cards 2BRI-2FXS PCI-E Interface (Sangoma B700), 4BRI-2FXS PCI-E Interface (Sangoma B700) and 4FXS PCI-E Interface (Sangoma A200) need two special power cables, "INLINE Molex 3.5" female to 5.25" male, 6cm" ref:26622A and "INLINE Molex Y-cable 3.5" 1x5.25" to 2x5.25" angled, 0.2m" ref:29659W in order to be able to connect them in the server.TE120 Series TE120P/TE121/TE122 User Manualĭigium, Inc. If this additional power connector isn't connected, the card will not function at all. Therefore an additional Molex 8981 Power connector needs to be connected from the SOP power supply to each FXS card. (1) FXS cards draw more power than a standard PCI or PCI-e slot can provide. The card needs to be inserted into a PCI Express slot. There is no molex connector on B500 card.Īfter plugging the molex cable (2) you can insert the card into the server. If a 4FXS card is used in combination with the BRI-FXS card, connect a clock sync cable between the 2 cards with the red cable on the opposite side of the slot (otherwise the driver won't start)īefore Inserting a B700 card into the server, connect a molex cable to the card. Step 2 - modules 2BRI & 2 FXS inserted into the card:įor a 4 BRI config, just add a second 2BRI module. Step 2 - modules 2BRI & 2FXS inserted into the card:įor a 4 BRI config, just add a second 2BRI module, like that:īy default, do not connect the FXS module, unless the customer wants to connect a modemĢBRI (4BRI) NT mode with or without 2FXS module When running in TE mode, ensure both termination resistors that correspond to the module are set to OFF.ĭefault the resistors settings are set to OFF which corresponds with TE mode.ĢBRI (4BRI) TE mode with or without 2FXS module When running in NT mode, ensure both termination resistors SW2 that correspond to the module are set to ON. TE is used to connect to provider network and NT is used to connect to another PBX or ISDN phones. Changing modes does not require jumpers, simply invert the colour-coded module. See below how to prepare the B700 and B500 cards.īRI modules can be used in TE or NT mode. So one B500 card can support these 2 configurations : 2BRI, 4BRI So one B700 card can support these 4 configurations : 2BRI, 2BRI-2FXS, 4BRI, 4BRI-2FXS Sangoma BRI-FXS hybrid cards (B700) and Sangoma BRI cards (B500) If a PRI or BRI-FXS card is used in combination with the FXS card, connect a clock sync cable between the 2 cards with the red cable on the opposite side of the slot (otherwise the driver won't start).If the PRI card is used in combination with a FXS card, connect a clock sync cable between the 2 cards with the red cable on the opposite side of the slot (otherwise the driver won't start).Please refer to this document to know which combinations of cards are allowed. Plug the card into a free PCI / PCI-X slot.Sangoma BRI-FXS hybrid cards (B700) and Sangoma BRI cards (B500)ĭepending on the region of the world and the specific task the PRI card will be used for, the "E1/T1" jumper switch should be changed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |